Showing results: 286 - 300 of 409 items found.
-
YAV90084A -
6TL Engineering
4x 8-Bit 1KOhm reostat 4x 8-Bit 40 Ohm reostat 2x 8-Bit 5 MOhm reostat 10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in selft test. 10x Voltage to current source 0(4)..20mA 10x Analog Outputs (Buffer for voltage or frequency) 36-Ch Test Point voltage divider 2xCAN Bus Channels Terminators tester Expandable with NI PXI-6723 and PXI-6345.
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
-
PCI-600 -
Manta Test Systems
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
Series HSM -
Kepco, Inc.
The Kepco HSM series comprises a group of ten models, seven 1000 watt power supplies with outputs from 3.3 volts to 125 volts and three 1500 watt power supplies with outputs from 24 to 125 volts. All models feature current sharing for parallel operation and redundancy applications. Kepco¹s 1000W HSM have a wide-range input (90-277V a-c). The 1500W models operate 180-277V a-c. Both incorporate power factor correction to meet EN 60555-2 and EN 61000-3-2. These modern power supplies operate at 100KHz using current mode control to provide rapid response to source and load changes and tight stabilization.
-
LDH400 Series -
Aim-TTi
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
Element 1 Power Systems Inc.
The fuel cell will change our lives as much as the computer it powers and the internal combustion engine it replaces. The future of power and transportation will change dramatically when fuel cells become the main producers of clean energy. The car will no longer be an environmental burden, and the electrical grid will be subdivided to the neighborhood and building level. The quality and reliability of this alternative energy source will be superior to the current grid design. Fuel cells and hydrogen technology will make all of this possible, and with little or no pollution.
-
NMR-EA300 System -
Caylar
The NMR-EA300 system is the reference for calibrating magnetic sensors. It allows to generate an absolute magnetic field at <±10mG (0.1 uT) without temperature drift (<0.1ppm/C°) over a range from 14mT to 3T. This system is composed of an EA300 electromagnet with NMR poles, a MPU-16U ±150A ±70V current source of class 1ppm and a NMR20 Teslameter with a magnetic field controller (FR020).A thermostat chamber can be installed in the air gap (Optionally available on 50mm and 70mm gap poles).
-
E4361A -
Keysight Technologies
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
E4362A -
Keysight Technologies
The Keysight E4362A is a 600W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4362A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
40-412A-024 -
Pickering Interfaces Ltd.
16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Manta Test Systems
Choose from Doble’s F6300e and F6350e External Amplifiers for your specific protection testing needs and requirements. These amplifiers are useful in high power protection testing applications when you need additional current and/or voltage sources, for critical high burden relay testing, as well as system modeling.
-
2672AM -
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
420001 -
Sper Scientific
When undertaking power installations, the 420001-insulation tester can provide special help to test wiring. This unit can provide 125V,250V, 500V and 1000V source for the test, and under each range it can supply 1mA current to feed the capacitance load. With the auto-range function, it can measure up to 4,000 Megaohm with the resolution of 1Kohm.
-
Series BOP-HV -
Kepco, Inc.
The Kepco Model BOP 500DM and BOP 1000DM are high voltage power sources, up to 500V or 1000V, respectively. These combine the capabilities of fast programmable power supplies with a Class A output stage, which can respond bidirectionally from zero. The BOP-HV can be operated in either a "voltage stabilizing" or "current stabilizing" operating mode (selectable by a front panel switch). These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
Lock-In -
OptoTherm, Inc.
Steady-state thermography is limited to detecting hot spots that heat up a minimum of 100 mK (0.100°C). This may be useful for locating shorts on high-power devices, but is inadequate for detecting low power defects such as semiconductor device leakage current or short circuit with very low or very high resistance. Steady-state thermography also suffers from poor spatial resolution as the heat from localized hot spots diffuses rapidly, blurring the location of the heat source.